Search the Community
Showing results for tags 'drive belt'.
Found 9 results
-
Hello everyone! Thought I would post a new thread on this as I wasn't able to find the information I was looking for. But I'm trying to get this drive belt on my 252-H and no matter what I try I can't get it on. I got a 1/2" x 76" so I know its the correct size belt. I followed the steps outlined in the manual which I've attached, and is shown on page 15. So I loosened the cross bar nuts and the flat idler adjustment pulley. And followed the routing from this guide: http://outdoorpowerinfo.com/repairs/wheel_horse_hydro_252-h_drive_belt.asp I just can't get enough slack on it to get it over the engine pulley! Right now it's pinched up between the body and the pulley so possibly I can't get enough leverage, do I need to somehow work it from below the pulley? Doesn't help the pulley keeps coming off the shaft so I have it propped up using a scissor jack which is cumbersome to work around. I don't have a shop or anyway I can think of to safely stand the mower up and not sure about tipping it on it's side. Anyone who has done this particular belt on this mower before have any tips or suggestions for how to get this thing on? Thanks for the help friends! CJ 492-4003 Eaton 7 & Peerless 1320 SM.pdf
-
Hi All, I have a 71 or 72 Model # 101006, Serial # 790336. Model number chart says 71 but the paper for the engine has a print code 72. The closest I could find was for models 1-3745 & 1-3741. Two questions. I finally need to replace the drive belt. This manual list the belt as # 1576. Two questions: 1) Does anyone know what size that translates to? I do have the old belt but the inside edge is falling apart so it will measure a little longer than it should. 2) This tractor has the electric clutch. What is the best way to remove the belt? As always...Thanks!
-
Hi there, sorry if this is a repeat question. Anyone have a pic or diagram of how to reassemble the pulleys / tensioner, and how to route the belt? One more...what are the 4 holes for at the rear of the seat deck (above the logo decal)? Cheers, Mike
-
Need help,. 244-h model 72041 newer. The drive belt keeps coming off is it to lose, to tight? Any ideas would be great
-
I had a drive belt let go on a 1980 C-175 Sundstrand hydro. After searching the manuals it looks like either an 83" or an 85 1/2" belt is called for. Anyone know the right length off the top of their head? Thanks
-
I need to change the Drive Belt on my Wheel Horse 208-4SB Model 42-08B401. I really need some step by step instructions or a service manual. I can't seem to find the procedure anywhere. PIctures would be great. My mower is slow going forward and It was suggested to me to change the drive belt. Thanks
-
can anyone tell me the size and number of drive belt from clutch to rear end on a 86-312-8 wh
-
C-165 Clutch Pedal takeoff and braking too suddenly
DaleLicht posted a topic in Transmissions and transaxles
Hi everyone, I have a 1984 C-165 with an 8 speed manual transmission and last year the drive belt started slipping and making noise when the clutch pedal was engaged (pushed down), so I figured that it was time to change the drive belt as it was very old. After changing the drive belt and also the brake band (there was no brake linings left on the old one) I now find that the when you engage the clutch the tractor brakes hard to a sudden stop, and at no time does the tractor disengage the transmission with out braking. I also am still experiencing some belt chatter when the clutch is engaged. Is this an adjustment that needs to be done or something else? Any help would be greatly appreciated, Thank you -
Need a new drive belt for my C-81. The process looks pretty much straight forward, but, experienced opinions can be very helpful. After looking at the PTO, should I remove that to do this correctly? Or just take bracket and pto lever off to facilitate removal? Thank you.
