Leaderboard

I went to shut my tractor off, removed the key, and noticed the engine was still running. A quick search on the site, and I found the ignition switch part #, and placed an order for the Stens switch with a well known jungle site. The tractor was up and running the next afternoon. Just a quick thank you for those keeping the site up and running.

Hey, you’re a supporter! Thank YOU for keeping this site up and running too!

I told myself, hold off ! no more for now. The force was just too strong today. I just had to pick up this B-80 8 speeder. Non running and lots of patina -aka Rust ! What’s not to like ? First in line tomorrow morning is a good pressure washing then too see if this old girl will run.

I'll never forget the guy who was at TSC and forgot the size of a needed belt. Whipped out his phone & posted here and in minutes was out the door with the correct belt.

Here are my Son's two Work Horses, both are unrestored and original paint, decals, tires etc. The one on the left is a 1982 LT-1137 and the one on the right is a 1984 LT-1100.

That is what it is all about, friends helping other friends and soon to be friends we haven't had the opportunity to meet yet.

Shine bright like a diamond.

And also staying in touch with already-met friends. All good.

Thank you very much for the information gentlemen. It’s always nice to get confirmation from the experts. Best part about it is I scored it at a small auction locally for $20! Also got an additional set of rear rims with turf tires for a dollar. Hoping to ‘rustore’ and eventually hit some meetups and shows. Thanks again. Bob.

As long as Wheel Horse is on the side… I like it !

Today I gave it a good pressure wash.I think it cleaned up pretty well 👍 Brought it in and tore into it.Had no spark,cleaned up the points, issue solved. Replaced the head gasket,was blown out pretty bad but the cylinder looked great and no piston slop at all 😮 I think I may have gotten lucky on this one.It’s always a crap shoot with a non runner. I think the trans is ok but won’t know for sure until tomorrow once I get it running.

@Lane Ranger Fixed this one for ya...right side... hurt my eyes...

Thank you for the 'thank you'...... all too often we will have a long back/forth discussing/suggesting/ a problem for a poster ---- and never hear what the outcome was for the poster.......

EB you know we don't read instructions! Most of us are in our second childhood. we like pictures. You should understand this, you never got out of the first one. You have to keep it simple our attention span is short. Pictures Needed "2" Wheel Horses Not One or More. See below

Perfect Richard.....that's why we're here.

Any idea what year? I have a '73 which is a no name but since a front runner to a B I call her Aunt B. Just had to give it a home for only a franklin... Yes Sir!

Had an old buddy who said it best: if it's got any compression at all, it will run!

Awesome! I bet a little soap and water wet sanding and that thing would have PURDY popping out of it everywhere! The one I’m sitting on, I wet sanded and buffed and it brought a ton of paint out of the rust that was on it.

I polished another hood today. Not perfect, because it's 25 years of scrapes and dings. But still pretty awesome for 20 minutes worth...

Huh? What?

Got them from the jungle site. PAR36 LED Landscape Light Bulbs 12W 1280LM 80W Halogen Landscape Bulbs Equivalent,12-36V Daylight 6000K

Yes Sir .This is my second b80 other is a 4 speed I use to cut the lawn and yard work, the k181s are a breeze to wrench on and little power houses for their size.

Wheelhorse#1 I have had many of these. Kept some sold most. Hard to beat these K181`s. Enjoy the ride. Looking forward to seeing more picks when done.

Just a couple. (Hehe)

After @WheelHorse_Kid pulled a few weeks ago his older brother Aiden has shown a little more interest in tractors. For those who don’t know him Aiden was my right hand man in the garage for years til he hit those preteen/teen years. His world revolves around baseball and plays 3 outta 4 seasons and practices in the off season. So it’s nice to see him back out in the garage and hopefully gets re bit with the horse bug. This late gray 60’s hydro that they got in a package deal that they purchased last winter with all their own money was his goal. Well today he took it for its first spin under its own power. Not the correct motor but still looks to be the correct horsepower. He’s currently out there in the driveway working with Alex and they are taking the plow off. The previous owner did not have a plow bracket so he installed the rod into the hitch on the back and then cut a hole in the fender pan for the turning arm. It’s missing a belt guard but I think I have one kicking around. He says he wants to keep it gray. Someone did a great job of free handing the decal area and even on the plow itself.

We used the Wally Digger Backhoe FEL to move more stone into the erosion control project area by the right side of the Pole Barn. Nearing completion on that deal.

My Prayers for those people in Maine that are a part of this tradgety. I consider myself a small part Mainer from my days there in the Navy. I know the whole state is like a small, friendly community. The healing process for this will take a very long time. Just know that you are not alone...this stabs us all in the heart.

Nice of you but Lane can't count to two, BBT isn't going to be too pleased!

The one above is ‘76. Yours Looks very nice and in great shape. Bigger rear tires make all the difference in my opinion.They Ride better and look cool .👍

to gt14ider thanks for the tip the key was missing and the pulley was half off the shaft fixed it in ten minutes. thanks again for the help. Brent

This is DEFINITELY true!!!

Check keyway at wheel hub to axle, transmission drive pulley to input shaft. Take a marker, put a line across hub across axle, try to move it and see if the line moved

Same boat.. I live dangerously and ask about certain items that don't seem to get any use in the sewing room. Happens every time she questions stuff in the garage. No I don't use my scroll saw daily but when I need it... I need it.

I think this is the link to the thread, and here's the video that was originally linked in post #10.

very nice man i might pick up a c series soon since round hoods are basically non existant

I've said that too Young Skywalker. Now we have 13 ..... There. Fixed that for ya.

Are we talking about an Eaton 1100 or a Sundstrand Hydro? Either way if the plate the transaxle bolts to is cracked or the bolts aren't tight that could be the bucking problem.

@JoeM Good to know about it sticking up a couple inches higher. Did you just cut the end off and re drill for the pin? Or cut section of shaft and weld? Did you notice a big difference in ease of steering?? Eric, I do have a 2 stage blower, but havent used it for a few years since the single stage does a good job and is much lighter. From your questions, it seems that itd be good on my 416 since i generally use it for mowing and bagging about once a month. This will likely be a winter project for me as i have 2- 12yr olds and a 14 yr old, so time is precious now. My 14 yr old shows some interest so ill have a helper.

Does not have to be ORIGINAL paint. Just looking for something that is CLOSE to original appearance.

Just waiting on the new sneakers to be delivered.

My winter rig getting some maintenance before snow flies…