Leaderboard

Well I guess I can actually play in this thread now...

Had to do some reconstruction on our IH 4700 today.. The floor in this truck was getting pretty soft. Here is a pic of the right side of the truck after I cut the rusted floor panels out. Rocker panels were also in bad shape. After a little tin knocking I was able make some new rockers out of some 16ga. New floors in & welded in place.

Electric fuel pump on the 953.

1925 Renault. Now in the ownership of a friend of mine.

While looking up on the Renault I came across this photo'. It's the very same one my friend now owns.

Probably worn pivot pin for the front axle. Pull the pin and see if it has grooves worn in it. I redid a Charger. Made a new pivot pin out of 3/4 stock. Drilled out the center hole in the front axle to 7/8" and pressed in to sleeve bearings (7/8 OD 3/4 ID) now nice and tight

Saw this beaut’ at the Orange Box Store today...

As far as firing once in a while, when you're done they need to be completely disassembled, washed with hot soapy water, dried, and reoiled. Black powder is very corrosive....

Today I decided it was time, as the pond has dried up, to de-reed the edges before they encroached any further. Hot work pulling the things out and after four hours as the sun came round, decided to call it a day. The Sears and Saxon trailer were brought into play, transporting seven full loads down the bridleway for disposal. I'll tackle the rest on Wednesday, as up at the farm tomorrow.

And finally, Don

What an afternoon. We went to visit the lovely widow we've been helping out and from whom we have received some things, and also purchased some things. Today we picked up the lathe, a slew of it's tools, and a few other odds and ends. Trina had a particular space already in mind for the lathe to set. Took a few hours this evening to clear the area and rebuild the table a bit. Here's the results:

Here's a link to the one from 2 years ago.

Been working on a complete engine rebuild. Moving slow but moving ahead.

Trina and I have been given the opportunity to be the owners/caretakers/stewards of a few hobby type handmade firearms. We do know that they are not super valuable but we'd like to give a fair amount for them. Age is unknown but I believe maybe 15 to 25 years. All of them were bought as kits from the Kittery Trading Post here in Maine. The firing ability of the three guns is unknown but I would have to assume that they work knowing the owner. The Cannon below does fire. We would appreciate whatever thoughts, questions, values, you can give us.

I'll throw one more caution out there. Before loading any muzzle loader, MAKE SURE it isn't allready loaded. Way too many front stuffers get put away loaded. I always file two marks on my ram rods to measore the barrel length. One for loaded and one for unloaded.

Ceiling is done in the barn Working on the walls now. 1 1/2" foam board between the purlins and then cover that with plywood underlayment.

That's one of the good things about living in Maine. It's pretty free state when it comes to that kind of stuff.

@ebinmaineGonna be hard to tow a wheel horse towing one of these behind that truck

Well sir, that's my version of a new horse hauler. The drivetrain and the nose is 86 Ford F250 HD. 300-6, 4 on the floor, 4WD, 4:10 gears. It has 43,000 original miles and I'm the third owner. It was originally purchased by a mason in central New Hampshire. Owned it for just a few years and retired. It sat for a long time and then the fellow I got it from bought it around 20 years ago and did a full frame off restoration somewhere around 2003. You'll note that the bed is of much newer vintage. Frame, running gear, nose, 1985 or 86. Cab is a 1995 but has the 1985 firewall grafted into it so as to be able to use the older style components. The bed is of 1997 vintage. That will actually be coming off and being sold in favor of a wooden flatbed. The last owner drove it as little as 300 miles per year over the last 20. When I bought it I knew it needed a few things. Nothing major. Finishing up type stuff. After we got it home I found out that it had a worn-out pinion bearing race and small chips in several teeth of the rear ring gear, likely due to the yoke being loose. The rear end will be completely rebuilt because I'd like to treat this truck the way things should be done. As some of you know, for quite a while now I've wanted to get a hold of a 300-6 and wake it up a bit, so to speak. This one is going to end up with the above intake and carb, later model EFI split exhaust manifolds, y-pipe going into single exhaust. Some sort of electronic ignition change and complete removal of all computer controlled engine components. Because this truck sat for so long there's a lot of oil seals and gaskets that need attention. If one of those turns out to be the rear main seal or transmission front seal then I'll have to pull the engine and at that point I would also put in an RV/Torque cam. She's a good old solid beast in overall excellent condition particularly for the area we live. It'll be a great cruiser that can also work. Fun yet practical.

I wanted to get some ags and ribs, so i called a friend up that restores Wheel Horses (what-up Ric!). He had some tires that were perfect. Some mounted Carlisles with tubes and brand new Deestone Air Locs with tubes. I had a local place mount the fronts to the original wheels. The rear tires were bigger than the originals I got it with, and the size was about perfect. You can see in some of the pics the difference. After getting it all mounted up, it turned out great! Up next is some deep cleaning and getting the mower deck up the snuff.

Hey everyone. I snagged my third Horse last week, which also happens to be my first "real" non-Toro produced Horse (my others being a 1990 312-H and a 2002 314-8)- a 1974 B-80. I always monitor local Horse selling activity around my area here in St. Louis, but given i didn't "need" to take on a project, I always have just been sitting on the sidelines. I noticed a B-80 went up for sale local for only $200, with a blade and wheel weights (!), that also appeared to be in sound mechanical condition. I messaged them right away and I was the first to say I'd pick it up sight un-seen, so it was mine. I went with a trailer and bam. Even better, it ran great! The only issue I could see was that the PTO was stuck on. Heck of a deal!

Gotta be stamped on the barrels..50 cal. is real close to a half inch. Or bust out your calipers and measure. Dueling pistols probaly around 30 cal.... ther ya go EB we got a new handle fer ya and the better half..... The Pistoleros ... or hey..... The Cannon Ballers......

Buy the cannon! Tow behind military tractor haha

I had a '67 Chev P.U. with a Stove Bolt strait 6 and a granny low 4speed. It had dual 2" exhaust with glass packs that made some beautiful music. (Just a suggestion)

I'd love a truck like that. Unfortunately the running costs over here would be prohibitive.

Spent some more time detailing the 500 this morning. Looking a little better. I did use a little touch up paint in some areas but I am trying to keep the patina. Still looking for a seat. I also will me working on the mower deck.

Care package from @oldredrider came today!

Nous pensons que vous avez assez de mal avec l'anglais!

after watching that I need a horn too

Hello from another Wheel Horse fan in Pace, Fl. I'm an old follower of this forum, but I just created an account. I bought a 1987 312-8 from the Hendrix boneyard back in 2004 after hurricane Ivan and restored it. Needed something for storm cleanup work. Still using it to this day! Between my neighbor and I, we now have 3 restored Wheel Horses.

Phew its hot here. Did a litter pick and collected 30 bags of rubbish thrown out of cars onto the road side. Also finished a project for a lady who has an old dog who she takes out in a stroller. The handlebar needed replacing so I fabricated a new one for her. I did it pro bono and she got me some beer to say thanks.

Check out this beauty of a survivor!

I can't believe I'm the one that landed this one off Facebook market place, It was listed for $850 for weeks. I watched the price. It kept dropping. I have four other GE Elec Traks and I sure did not need another. One day I made a low off and included that the price was only good if they would deliver. They took it and I even got it cheaper than my offer. The battery's is only 3 years old. So far everything's working except the head lights. I'm happy... I'll get some better pictures. This was one of the posted for sale pictures.

Like Eric sez, if you want to find info on pros/cons of this awful stuff we now have to use for fuel --- well, plan on some time, there are dozens of posts on here re this subject. But to save you the trouble, the bottom line is to just DO NOT use the stuff in ANY small engine.... period!! Either find a source to buy ethanol free at the pump, or failing that use one of several additives to add to the regular stuff - Stabil seems to be the most popular, but there are several brands that would probably work also. My local Wal Mart has been carrying ethanol free for the last 2-3 yrs but for some reason they no longer have it, and the other 3-5 stations that carried it dont have it either??? So for the last few months I have been adding Stabil to my equipments fuel......

Thanks Eric. Yeah I'm going to remove the whole pan for this and will find a spot to be able to safely hammer the crap out of it, haha. I used to work for a company that sold power hammers. If only I had access to one! I should have some time to do this later in July and will post pics when I do!

I mulled over how to do the exhaust for several weeks. The reason I ended up going with a 6 into 2 into 1 was mostly based on cost and simplicity. I don't have any connections to get good pricing on exhaust being custom built and it ain't cheap. The Walker y pipe I have will dump out just over the top of the transmission crossmember so with the muffler at the end of that all I'll need is a turn down.

Almost there bud. I need to clean out the carburetor and get the engine to set in place. Figure out a small exhaust. Trina has a few more decals to put on.

Man the timing on that one is excellent. Fits better than one could imagine.

Had the seat cover made at an upholstery shop, the took it an embroidery shop for the horse. $170 for the cover. $20 for the embroidery. I thought 170 was pretty high, but maybe not. He did do a great job.

Maybe a 518? Onan coils were only controlled by the pto switch and seat switch in Wheel Horse long frame models. Oil pressure switch in 1988 controlled just the light.

I found a good spot under the dash for USBs. Now speakers and cup holders on the list

Start with a carb cleaning. Your well intentioned maintenance may have dislodged some crap. Did you replace fuel lines/ filter. May have sat with ethanol in it's go juice. Looks like you might have?

Finally some decent weather. Hay cut Thursday afternoon, Tedded Friday and Saturday. Rowed up Sunday morning, baled Sunday evening. Temperature 31c here at the moment! C121 getting a good run towing the trailer around collecting bales.

Leaning towards using a Derale 15300 trans cooler and water separator to keep water out of the tank. I seen a few videos on YouTube. Air temp into the cooler is 260+ and 80 out. Seems to work well. Thoughts? Thanks.

Excellent!! You basically purchased a plow OR wheel weights and got the rest for free. Niiiiice find!!