Leaderboard

Very rare full length saw sharpening vise 26” long. Ordinary they are 10” to 14” long forcing one to reposition saw at least once during sharpening which is a major annoyance.Been looking for one close to 15 years finally scoring this one.

Let's see... It's Green, with yellow trim... It ended up dying... yep - it's a John Deere.

First time in at least 20 years this tractor ran and drove!!! 2nd pull it came to life, no smoke no noises,. Wow this is light in the front, I never drove one of these, even at 1/2 spd and 2nd gear she wants jump. I have to figure out something with the throttle cable. I can see why people hacked these hoods up back in the day

1st gas up, and ride completes the resto! 20200909_132602.mp4

Got the 854's HL-5 set reinstalled today. After dark...

A friend of mine was at a auction this last Monday and I found out what he brought home and I had to ask if it was for sale it’s a tiger 450 I don’t know a bunch about it Same rear end as a suburban but I thought it was neat and I believe kinda rare it was bought from original one owner

Yes, the shaft can be sleeved to 1 1/8. https://www.ebay.com/itm/1-to-1-1-8-inch-1-4-Key-Gas-Engine-Pulley-Crank-Shaft-Sleeve-Adapter-Predator/252430716490?hash=item3ac60b0e4a:g:1JwAAOSwOIlbza8~

My father passed away in January, and has had this garden tractor for as long as I can remember. I am contemplating a restoration as a memorial to him. He was an avid "puller" in the early 80's and even a hobby puller later on. I know this piece doesn't have a lot of original, but I would love to put it back to the state he would have pulled it in the 80's. First step is to find out what it is. I believe it to be early to mid 60's. I have no idea from there. The serial number plate is still there, but only "61862" is legible. Any help/history would be awesomely recepted. Thanks for helping a newby out.

@Rp.wh

That would be the implement lift handle.

There are lots of good members here that will help you through any problem you may encounter. If you have an electric motor hanging around you could belt it up to the transmision to bench test it.

With out an engine and belt there is nothing to hold the transmission input pulley from spinning, so it will roll in every gear. After you find an engine for it and get it installed, I would change the fluid in the transmission and give it a try. If there is an issue with the tranny we will gladly help you through that process.,

Loaded up the Cargo Pro trailer with it's first WH for a ride back to Maine. This one will be at the Meet & Greet without all it's sheet metal, just didn't want it to miss out on all the fun.

God must have had a message for us in this transformation, how else could something that ugly transform into somethin so beautiful. .

@BOB ELLISON is the best, he made the seat cover for my 1055.

At this point, 6oh...whatever you want it to be! The point is to have fun with it like your Dad did, that's how you honor his memory.

They're made out of metal. Mostly flat. Probably painted red. Does that narrow it down at all?

Aaand next step... because i see after hard rain the last few Day‘s lightly oxydation on the tie rod ends, i decide to change them to Waterresistant Versions from light Cars. So i mounted them today on and after dismount the Frontwheels, i see there are Ballbearings. That‘s the great issue, but i also see while lifted frontaxle a wear in the spindles. i called a friend, if he is able to rework that for me and may bushing it? He told me yes, but you hopefully not in a hurry otherwise i must pass. I told him i have time and will be patient until he had more time to do that. for me it‘s actually not a hurry, but if he can redo, i wanna have it qualified and that needs it‘s time i know that. At least i found few fence post caps, they will fit as Waterprotection caps over the spindle tops, looks pretty slick and water have no chance further to penetrate my frontaxle Spindles. they be 34 mm in diameter and with a bit force, they will fit snug over the Spindleends. After that was done, i did a testdrive with the mole rake. The first completely non rainy day since a Week. Btw, i love that electric impact wrench i bought, it‘s fairly fix and works perfect for the horse. the whole change depends just 12 min. Cool 😎

I'll bet @WHX24 has a guard that will fit your 308-8. Welcome to Red Square. I'd say there is nothing wrong with your trans, but what you could do (instead of pushing it around) is jack up the rear end and try a few things that way. 1. with both wheels off the ground and the trans in neutral...spin one of the wheels in a direction...the other wheel should spin in the opposite direction. Do the same with the other wheel. If it works both ways, with no slips or funny noises, then your differential is good to go. 2. put trans into 1st gear...turn the intake pulley in a counter-clockwise direction...one or both wheels will turn in a forward direction. 3. Repeat with the rest of the gears. when you get to reverse, the wheels should turn in that direction. 4. Don't be shocked if only one wheel turns...simply get someone to hold that wheel from turning, and the other one should start to turn. 5. If you can shift between hi and low range, then that part is good. 6. If all goes smooth, you have a good trans.

Rotella 30W with Rislone zinc additive...you will feel the difference immediately.

I personally have all of them

I gave the retired C-120 a little exercise. Hauled a tree stand and me to the back 40. 20' up and no broken bones Kevin.

Home safe!

Please post some picts of your resto here to inspire us.

Many of the WHs with the fuel tank under the seat require some priming if they haven't been used for awhile, or if you've just changed the filter or lines. Take the disconnected fuel line, and route it downhill from the fuel tank valve. If you don't get any fuel by gravity feed, then the problem is inside the tank, either a clogged filter on the valve, or a defective valve. I usually empty the tanks and rinse them with fresh gas whenever I do a rebuild. It's amazing how much junk can collect there. Usually have to also replace the valve. If the fuel flows with just gravity, then you might want to put an inline primer bulb to get it to flow uphill to the fuel filter and pump. I bought marine type primer bulbs with 6mm connections on ebay, and they work great on three of my tractors. Good luck, Jim

What a great way to honor your Father!

They found it!!!! They found it!!! The Island of Misfit Guards!!!

to firstly Sorry for your loss, second i like the idea of a memorial Horse. Awesome little Machine. i hope you have a lot of Fun with it.

Really stoked about being able to get it .Didn't come cheap at all but when one sees something like this there is never time to worry about money if one really wants it. Many eyes out there looking for the same thing. To my knowledge the first one that has come to light in at least 15 years. Of course as usual now will probably start to show up once owners now how much it is worth.

My mother is English, she gives me my dry sense of humour. I'm sure you've heard of bailing wire mechanics or perhaps even watched a few Red Green duct tape episodes where he uses duct tape to repair most everything. Matt prefers using his welder.

Nice piece. It found a home with a person who knows how to use it.

30 weight shell Rotella. All l use

Good line, I like that.

I would think you would be hearing more than what you are hearing if the trans is bad... I'd go with @Achto and @ebinmaine's advice...

If in every gear you push it and the input pulley of the transmission is turning, the chances are the transmission is good. The only way to know for sure of course is to break it open and check things over.

I don't use Lucas but I do use Mobile. Same thoughts with no issues. Racing oil is probably a better choice than additives. I managed heavy industrial maintenance for over thirty years and found oil manufactures have lots of products designed and engineered to match the need. I always looked at additives as if you take vitamins cause your diet is poor. I am not brand loyal and most major manufactures have some kind of racing or high performance fluids. This is just the info sheet from Mobil. mobil-1-racing-product-guide.pdf

Thank you all for the help. I had some rubber wire grommets that fit. They've got a hole in the middle for wires, but still work great as bumpers. Man, I was getting annoyed at the way those tabs were scuffing the paint. Now it all makes sense. 😂

We like door knobs!

You know those aren't deer in the field right Ed???

Here is the brochure this is everything that they made for the seniors Wheel-Horse-Ride-Away-Sr-Brochure.pdf

Nice haul Tom!! Wife & I are having a staycation this weekend. But ya I'm a bit tractor heavy. Jim may be tractor heavy, but he still would have been all over that haul if he wasn't dedicating this weekend to score some Joe Exotic underwear before supplies are gone.

I like them too and always save old ones from the many jobs over the years. Quite a few here.

There may be one in that pile there may not. Trouble is I have no idea what some are for. Someone would have to put up a pic of what the correct one looks like.

I go with caterpillar. Try doing a Google search for large green blah blah blah something like that

Hey Seth, Once it stalls, does a short rest allow it time to recover and it’ll start back up? When it stalls, will it still crank but not fire up? Try loosening the gas cap and try immediately again. If you have a spare spark plug, it would be a quick check to see if it has spark as well. Pull a plug wire off the plug on one cylinder, pop it onto the spare plug and PROPERLY ground the plug body (metal) to the engine, then crank it over. Determining if you are loosing spark or fuel will help immensely.

The dash tower tells me it’s a 64’ model...if the hood is original my next guess would Maybe be a Tecumseh powered 654/604 model tractor. It would be cool for you to redo this tractor...

Garage yes. No heat. Stabil for gas. Critters are “relocated” as needed...